Online 300-430 Test Brain Dump Question and Test Engine
Real Cisco 300-430 Exam Dumps with Correct 355 Questions and Answers
Cisco 300-430: Details + Topics
This test is also called Implementing Cisco Wireless Networks or ENWLSI. It is among the concentration exams for CCNP Enterprise that you need to choose from. You select it from a list of tests that also include Cisco 300-410, Cisco 300-415, Cisco 300-420, Cisco 300-425, and Cisco 300-435. The 300-430 exam is offered in English and Japanese only, and you will have 1 hour and 30 minutes to deal with about 60 questions. The expected question formats include testlets, multiple choice, and fill-in-the-blank.
The Cisco 300-430 exam is administered through Pearson VUE and the registration fee is $300. The official passing score is 825 points, so try to earn more than that. If you want to schedule this test, you have to create an account on the Pearson VUE platform and follow the instructions up to the end.
NEW QUESTION # 180
All APs are receiving multicast traffic, instead of only the APs that need it. What is the cause of this problem?
- A. The multicast group includes all APs
- B. The wrong multicast address was used
- C. The multicast group is assigned the wrong VLAN
- D. Multicast IGMP snooping is not enabled
Answer: D
Explanation:
If all APs are receiving multicast traffic instead of only those that need it, it indicates that Multicast Internet Group Management Protocol (IGMP) snooping is not enabled. IGMP snooping is a feature that allows a network switch to listen to IGMP network traffic and ensure that multicast packets are only sent to the ports associated with interested receivers, thus preventing unnecessary traffic on the network. References := CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide
NEW QUESTION # 181
A network engineer is configuring a Cisco FlexConnect AP to allow Cisco ISE to dynamically assign the subnet of a user based on their credentials. Which controller mapping must be modified for this feature?
- A. VLAN ACL
- B. WLAN VLAN
- C. RF group
- D. AP group
Answer: B
Explanation:
WLAN VLAN mapping is the answer. D. is incorrect there is no dynamic vlan configuration done there. You need to add the VLANs that you will dynamically assign to the WLAN VLAN mapping.
NEW QUESTION # 182
An engineer is configuring a BYOD deployment strategy and prefers a single SSID model.
Which technology is required to accomplish this configuration?
- A. identify service engine
- B. mobility service engine
- C. wireless control system
- D. Prime Infrastructure
Answer: A
Explanation:
NEW QUESTION # 183
CMX Facebook Wi-Fi allows access to the network before authentication. Which two elements are available? (Choose two.)
- A. Allow SNMP traffic only before authentication and block all the traffic.
- B. Allow HTTP traffic only before authentication and block all the traffic.
- C. Allow HTTPs traffic only before authentication and block all other traffic.
- D. Allow all the traffic before authentication and intercept HTTP only.
- E. Allow all the traffic before authentication and intercept HTTPS only.
Answer: C,D
Explanation:
NEW QUESTION # 184
A new MSE with wIPS service has been installed and no alarm information appears to be reaching the MSE from controllers. Which protocol must be allowed to reach the MSE from the controllers?
- A. CAPWAP
- B. SOAP/XML
- C. SNMP
- D. NMSP
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/mse/7-6/MSE_wIPS/MSE_wIPS_7_6/MSE_wIPS_7_5_chapter_01000.html NMSP (Network Mobility Services Protocol) - The protocol used for communication between Wireless LAN Controllers and the Mobility Services Engine. In the case of a wIPS Deployment, this protocol provides a pathway for alarm information to be aggregated from controllers to the MSE and for wIPS configuration information to be pushed to the controller. This protocol is encrypted. https://www.cisco.com/c/en/us/td/docs/wireless/technology/wips/deployment/guide/WiPS_deployment_guide.html#pgfId-80073
NEW QUESTION # 185
After looking in the logs, an engineer notices that RRM keeps changing the channels for non-IEEE 802.11 interferers. After surveying the area, it has been decided that RRM should not change the channel. Which feature must be enabled to ignore non-802.11 interference?
- A. Avoid Cisco AP Load
- B. Avoid Persistent Non-WiFi Interference
- C. Avoid Non-802.11 Noise
- D. Avoid Foreign AP Interference
Answer: B
Explanation:
The feature that must be enabled to ignore non-802.11 interference is "Avoid Persistent Non-WiFi Interference." This setting allows the Radio Resource Management (RRM) to not react to non-802.11 noise and interference, which can be crucial in environments where such interference is common but does not significantly impact wireless performance. By enabling this feature, RRM will not change the channel in response to non-IEEE 802.11 interferers, thus maintaining a stable channel plan. References := (CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide)
NEW QUESTION # 186
Which three properties are used for client profiling of wireless clients? (Choose three.)
- A. hostname
- B. DHCP
- C. MAC OUI
- D. HTTP user agent
- E. IP address
- F. OS version
Answer: B,C,D
Explanation:
NEW QUESTION # 187
An engineer configures Cisco CMX. which uses Layer 2 high availability on primary and secondary CMX instances, according to these specifications:
- Primary CMX IP address: 192.168.1.4/24
- Secondary CMX IP address: 192.168.4.4/24
- Virtual IP address: 192.168.4.1/24
During testing, the engineer discovers that the failover fails. Which action resolves the issue?
- A. Place the primary CMX IP address and the secondary CMX IP address in the same subnet.
- B. Place the secondary CMX IP address and the virtual IP address in different subnets.
- C. Place the primary CMX IP address and the virtual IP address in the same subnet.
- D. Use a virtual IP address with CMX Layer 3 high availability.
Answer: A
NEW QUESTION # 188
Which component must be integrated with Cisco DNA Center to display the location of a client that is experiencing connectivity issues?
- A. Wireless Intrusion Prevention System
- B. Cisco Connected Mobile Experiences
- C. Cisco Mobility Services Engine
- D. Cisco Hyperlocation Module
Answer: B
Explanation:
NEW QUESTION # 189
An engineer must configure a Cisco WLC to support Cisco Aironet 600 Series OfficeExtend APs. Which two Layer 2 security options are supported in this environment? (Choose two.)
- A. Static WEP + 802.1X
- B. 802.1X
- C. WPA+WPA2
- D. Static WEP
- E. CKIP
Answer: C,D
NEW QUESTION # 190
An engineer configured a Cisco AireOS controller with two TACACS+ servers. The engineer notices that when the primary TACACS+ server fails, the WLC starts using the secondary server as expected, but the WLC does not use the primary server again until the secondary server fails or the controller is rebooted. Which cause of this issue is true?
- A. Fallback is enabled
- B. Fallback is disabled
- C. DNS query is disabled
- D. DNS query is enabled
Answer: B
Explanation:
NEW QUESTION # 191
An engineer has implemented 802.1x authentication on the wireless network utilizing the internal database of a RADIUS server. Some clients reported that they are unable to connect. After troubleshooting, it is found that PEAP authentication is failing. A debug showed the server is sending an Access-Reject message. Which action must be taken to resolve authentication?
- A. Disable the server certificate to be validated on the client.
- B. Replace the client certificates from the CA with the server certificate.
- C. Use the user password that is configured on the server.
- D. Update the client certificate to match the user account.
Answer: D
NEW QUESTION # 192
An engineer must implement rogue containment for an SSID. What is the maximum number of APs that should be used for containment?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
Explanation:
NEW QUESTION # 193
On a branch office deployment, it has been noted that if the FlexConnect AP is in standalone mode and loses connection to the WLC, all clients are disconnected, and the SSID is no longer advertised. Considering that FlexConnect local switching is enabled, which setting is causing this behavior?
- A. Client Exclusion is enabled
- B. FlexConnect Local Auth is disabled
- C. 802.11r Fast Transition is enabled
- D. ISE NAC is enabled
Answer: B
Explanation:
NEW QUESTION # 194
Which AP model of the Cisco Aironet Active Sensor is used with Cisco DNA Center?
- A. 4800i
- B. 3800s
- C. 1800s
- D. 3600e
Answer: C
NEW QUESTION # 195
A wireless engineer must implement a corporate wireless network for a large company in the most efficient way possible. The wireless network must support 32 VLANs for 300 employees in different departments.
Which solution must the engineer choose?
- A. Configure one single SSID and implement Cisco ISE for VLAN assignment according to different user roles.
- B. Configure different AP groups to support different VLANs, so that all of the WLANs can be broadcast on both radios.
- C. Configure 16 WLANs to be broadcast on the 2.4-GHz band and 16 WLANs to be broadcast on the
5.0-GHz band. - D. Configure a second WLC to support half of the APs in the deployment.
Answer: A
NEW QUESTION # 196
An engineer is using Cisco Prime Infrastructure reporting to monitor the state of security on the WLAN.
Which output is produced when the Adaptive wIPS Top 10 AP report is run''
- A. last 10 wIPS events from monitor mode APs
- B. last of 10 sniffer mode APs with the most wIPS events
- C. last of 10 monitor mode APs with the most wIPS events
- D. last 10 wIPS events from sniffer mode APs
Answer: A
NEW QUESTION # 197 
Refer to the exhibit. Which two items must be supported on the VoWLAN phones to take full advantage of this WLAN configuration? (Choose two.)
- A. TSPEC
- B. 802.11e
- C. APSD
- D. SIFS
- E. WMM
Answer: B,E
Explanation:
Explanation/Reference:
NEW QUESTION # 198
When using a Cisco Catalyst 9800 Series Wireless Controller, which statement about AutoQoS is true?
- A. It automates deployment of wired QoS and makes wireless QoS implementation easier
- B. It matches traffic and assigns each matched packet to QoS groups
- C. It has a set of predefined profiles that you cannot modify further
- D. It allows the output policy map to put specific QoS queues into specific subgroups
Answer: B
Explanation:
Auto-QoS matches traffic and assigns each matched packet to qos-groups.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-2/config- guide/b_wl_17_2_cg/wireless_auto_qos.html
NEW QUESTION # 199
......
Valid 300-430 Test Answers & Cisco 300-430 Exam PDF: https://prep4sure.dumpsfree.com/300-430-valid-exam.html